 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Product Data Sheet Not Recommended For New Designs VCO-600A Voltage Controlled Saw Oscillator Features * Output Frequency @ 155 MHz to 1 GHz * Low jitter, 3pS rms for 622.080 MHz version and 6pS rms (typical) for 155 MHz version * Ideal for clock smoothing, frequency translation, clock and data retiming applications * 10K ECL, PECL logic levels with fast transition times * Complementary outputs * Low profile, surface mount package * Output disable feature * Low-frequency clock through feature * Miniature hermetically sealed ceramic surfaceThe VCO600A Voltage Controlled SAW Oscillator mount package (SO-28, approx.0.7in. x 0.3in) Applications * OC192/OC48/OC12 Clock Smoothing * Frequency Translation Description The VCO600A is a SAW stabilized, voltage controlled oscillator that operates at the fundamental frequency of the internal SAW filter. This filter is a high stability, high-Q quartz device that enables the circuit to achieve low phase jitter performance over a wide operating temperature range. The oscillator is housed in a hermetically sealed 28-lead surface mount package. It has a unique output disable and clock through feature to facilitate on-board testing. Vectron International 267 Lowell Rd, Hudson NH 03051-4916 Tel:1-88-VECTRON-1 e-mail: vectron@vectron.com VCO-600A Voltage Controlled SAW Oscillator Pin Information Table 1. Pin Function Pin Symbol 2,12,27 4 5,6,7,8 10 17 19 21 23 25 1,3,9,11,13,14,15, 16,18,20,22,24,26,28 VCC CLKIN 1 NC VEE VBW 2 VC OD3 CLKOUT CLKOUT GND Function Positive Supply Test Clock In No Connect Negative Supply Modulation Bandwidth Adjust Control Voltage Output Disable ECL Output Complementary ECLOutput Case and Circuit Ground Top View of Package 1. By setting OD low, a test signal may be applied at CLKIN and fed through the VCO-600A to both the CLKOUT and CLKOUT to facilitate on board testing. The test signal input applied at CLKIN may be either an ECL or sinewave input (up to 1Vpp, AC coupled). CLKIN is biased internally to VBB (Vcc-1.3V) 2. An optional capacitor to ground can be placed on VBW to reduce the modulation bandwidth for narrow bandwidth phase-lock loop applications. The modulation bandwidth will be approximately 1/(12000*C)Hz, where C is equal to the capacitance in Farads. If the optional capacitor is not utilized, VBW becomes a no connect (NC) and the modulation bandwidth will be approximately equal to the nominal device frequency /1200. 3. By setting OD low, the outputs are disabled and CLKOUT is held Low while CLKOUT is held High. The threshold for OD is 1.4V above VEE. OD should not be driven above mid supply and during normal operation, should be left floating (use with an open collector or 3-State gate for interfacing with standard logic). If the OD feature is used during normal operation, then CLKIN should be tied through 10K to GND to avoid any possibility of chatter on the CLKOUT outputs. Performance Characteristics Table 2. Electrical Performance Parameter Center Frequency, see ordering information Operating Temperature Supply Current Supply Voltage1 Absolute Pull Range (Vc= -0.5 to -4.5) Positive Gain Transfer (freq vs Vc) 155.520MHz Positive Gain Transfer (freq vs Vc) 622.080MHz Linearity Frequency Stability, -40 to 85 wrt 25C Output Level Low2 Output Level High2 Output Rise Time3 Output Fall Time3 Spurious Suppression Data Symmetry Control Voltage Input Impedance Control Voltage Modulation Bandwidth4 Control Voltage Range Output Current Storage Temperature Soldering Temp./Time Symbol FN TOP IEE VEE APR KV KV Lin FSTAB VOL VOH tR tF SYM Zc BW VC IOUT TS TLS Minimum 155 -40 -4.5 50 175 60 Typical 25 55 -5 350 135 3 150 250 250 -60 49/51 10 500 - Maximum 1000 +85 70 -5.5 700 290 Units MHz C mA V ppm ppm/V ppm/V % ppm V V pS pS dB % K kHz V mA C C/S -1.95 -0.98 100 100 -50 45 8 VEE -55 - -1.63 -0.75 400 400 55 12 VCC 20 125 240/10 1. The VCO-600A may be configured for PECL operation. All outputs and inputs including VC are referenced to Vcc 2. Output Levels are standard 10K ECL and are fully 100K ECL compatible. 3. Transition times are measured from 20% to 80% of a full 10K ECL level swing. 4. The modulation bandwidth is a function of nominal center frequency and may be adjusted down through the use of an external capacitor on pin 17. Please see Figure 1 and Figure 2 along with Notes 1, 2 and 3. Table 3. Typical Single Side-Band Phase Noise (dBc/Hz) Offset from Carrier VCO600A 622.080 100 Hz -50 1 kHz -80 10 kHz -110 100 kHz -130 1 MHz -145 Vectron International 267 Lowell Rd, Hudson NH 03051-4916 Tel:1-88-VECTRON-1 2 e-mail vectron@vectron.com VCO-600A Voltage Controlled SAW Oscillator +5 V +3V, 50ohms 2,12,27 VCC 0.5 to 4.5V VCO-600A 19 OUT Control Voltage OUT Output Disable Test Clock In 23 25 21 4 VEE 10 17 Ground Optional Capacitor Reduces Bandwidth 1,3,9,11,13,14,15,16,18,20,22,24,26,28 Figure 1. PECL Operation -5 V -2V, 50ohms 10 VEE -4.5 to -0.5V VCO-600A 19 23 OUT Control Voltage OUT Output Disable Test Clock In 25 21 4 VCC 2,12,27 17 Ground Optional Capacitor Reduces Bandwidth 1,3,9,11,13,14,15,16,18,20,22,24,26,28 Figure 2. ECL Operation 1. By setting OD low, a test signal may be applied at CLKIN and fed through the VCO-600A to both the CLKOUT and CLKOUT to facilitate on board testing. The test signal input applied at CLKIN may be either an ECL or sinewave input (up to 1Vpp, AC coupled). CLKIN is biased internally to VBB (Vcc-1.3V) 2. An optional capacitor to ground can be placed on VBW to reduce the modulation bandwidth for narrow bandwidth phase-lock loop applications. The modulation bandwidth will be approximately 1/(12000*C) Hz, where C is equal to the capacitance in Farads. If the optional capacitor is not utilized, VBW becomes a no connect (NC) and the modulation bandwidth will be approximately equal to the nominal device frequency /1200. 3. By setting OD low, the outputs are disabled and CLKOUT is held Low while CLKOUT is held High. The threshold for OD is 1.4V above VEE. OD should not be driven above mid supply and during normal operation, should be left floating (use with an open collector or 3-State gate for interfacing with standard logic). If the OD feature is used during normal operation, then CLKIN should be tied through 10K to GND to avoid any possibility of chatter on the CLKOUT outputs Vectron International 267 Lowell Rd, Hudson NH 03051-4916 Tel:1-88-VECTRON-1 3 e-mail vectron@vectron.com VCO-600A Voltage Controlled SAW Oscillator 622.080MH 51.840MHz and Freq Detector Loop Filter VCO-600A 622.080MHz Divide by 12 Figure 3. Typical Frequency Translation Diagram 155.52MHz 155.52MHz and Freq Detector Loop Filter VCO-600A 155.520MHz Figure 4. Typical Clock Smoothing Diagram Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can permanently damage the device. Functional operation is not implied at these or any other conditions in excess of conditions represented in the operational sections of this data sheet. Exposure to absolute maximum ratings for extended periods may adversely affect device reliability. Table 4. Absolute Maximum Ratings Parameter Symbol Power Supply VEE Output Current1 Iout Output Current2 Iout Voltage Control Range1 VC Voltage Control Range2 VC 1 Limts beyond which performance can not be guarenteed. 2 Limits beyond which device life may be impaired. Ratings -8 to 0 20 50 VEE to VCC VEE-0.5 to VCC+0.5 Unit V mA mA V V Qualification Conformance The VCO-600A family has undergone, and passed, the following Mil-Std qualification. Table 5. Environmental Compliance Parameter Mechanical Shock Mechanical Vibration Solderability Gross and Fine Leak Resistance to Solvents Conditions MIL-STD-883C 2002.3, TEST A MIL-STD-883C 2007.1, TEST A MIL-STD-883C 2003.5, MIL-STD-883C, 1014.7, 100% Tested MIL-STD-883C 2016 Handling Precautions Although ESD protection circuitrry has been designed into the the VCO-600A, proper precautions should be taken when handling and mounting. VI employs a human body model and a charged-device model (CDM) for ESD susceptibility testing and design protection evaluation. ESD thresholds are dependent on the circuit parameters used to define the model. Although no industry wide standard has been adopted for the CDM, a standard HBM of resistance=1.5Kohms and capacitance = 100pF is widely used and therefore can be used for comparison purposes. Table 6. ESD Ratings Model Human Body Model Charged Device Model Minimum 1000 V 1000 V Vectron International 267 Lowell Rd, Hudson NH 03051-4916 Tel:1-88-VECTRON-1 4 e-mail vectron@vectron.com VCO-600A Voltage Controlled SAW Oscillator 220 183 150 60s. 60-90s. 45-60s. Tim e(s) Figure 5. Suggested IR profile VI Figure 6. Outline Diagram Vectron International 267 Lowell Rd, Hudson NH 03051-4916 5 Tel:1-88-VECTRON-1 e-mail vectron@vectron.com VCO-600A Voltage Controlled SAW Oscillator J C B A E Bottom Holes for TRU and VCO Products Only G D F I L H K Figure 7. Tape Reel Drawing Table 7. Tape and Reel Dimensions (mm) Tape Dimensions Product A B C D E VCO600A 32 14.2 1.5 4 16 Reel Dimensions F G H 1.78 21 13 I 100 J 5 K 33 L 330 # Per Reel 200 Ordering information Table 8. Part number ordering information Part Number Packaging VCO600A 155.52MHz Tube VCO600A 155.52MHz Tape and Reel VCO600A 278.528MHz Tube VCO600A 278.852MHz Tape and Reel VCO600A 311.040MHz Tube VCO600A 311.040MHz Tape and Reel VCO600A 368.640MHz Tube VCO600A 368.640MHz Tape and Reel VCO600A 622.080MHz Tube VCO600A 622.080MHz Tape and Reel VCO600A 666.5143MHz Tube VCO600A 666.5143MHz Tape and Reel Comcode 107040537 407611896 107316457 107012551 107237539 407875244 107012569 407961762 330016544 330018383 For Additional Information, Please Contact: USA: Vectron International, 267 Lowell Rd, Hudson, NH 03051 . . . . Tel: 1-88-VECTRON-1 EUROPE: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tel: +49 (0) 3328-4784-17 ASIA: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tel: +86-21-28909740 Fax: 1-888-FAX-VECTRON Fax: +49 (0) 3328-4784-30 Fax: +86-21-28909240 Vectron International reserves the right to make changes to the product(s) and or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. VCO600A.DOC (REVISION DATE: 11/23/04) For Additional Information, Please Contact: Vectron International 267 Lowell Rd, Hudson NH 03051-4916 6 Tel:1-88-VECTRON-1 e-mail vectron@vectron.com |
Price & Availability of VCO600A6665143MHZ
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |